Filter Cartridge for Particulate Removal - FO Series
Velcon FO Series features high efficiency particulate media and a long service life. FO Series cartridges extend coalescer life and protect critical equipment downstream.
Features Include:
• EI 1590 Qualified Filter Cartridges
• Large Surface Area – Allows high flow rate with low initial pressure drop and maximum contaminant holding capacity.
• Resinated Media – Maintains strength resists effects of water and heat.
• 75 PSI Collapse Strength – Heavy gauge carbon steel center tubes give safety margin against pressure surges.
• Coated Steel Components – Resist corrosion from most industrial fluids.
• Corrugated Media – More surface area ensures longer service life.
• Buna-N Gaskets – The best general gasket material available assures positive seal in most fluids.
• Thermoset Bonding Material – Durable endcap-to-media bond prevents internal bypassing
• Threaded base filter cartridges – Available for easier installation.
• These are also available in screw-base design
Applications:
Velcon Pleated Media Cartridges are suitable for a broad range of polar and non-polar fluids. Recommended for applications where the contaminant is granular (non-colloidal), allowing maximum utilization of the high surface area.
Suitable for:
• Jet Fuel
• All Hydrocarbon Fuels
• Cutting Oils
• Glycols
• Degreasing Fluids
• Water Emulsion Coolants
• Naphtha
• Lube Oils
• Ethyl Alcohol
• Insulating Oils
• Toluene
• Synthetic Oils
• Hydraulic Oils
• Diesel Fuel
• Biodiesel Fuel
Specifications:
• Recommended changeout differential pressure - 25 psid
• 75 psi Collapse strength
• Micron ratings from 1/2 to 75
• 98%+ Nominal filtration efficiency
• 5 - 9 Operating pH range
• 250°F Maximum operating temperature
• Multi-pass (Beta Ratio) data available on request
• For information about Flow Ratings with various viscosity fluids, refer to Form #1532
• Flow rate depends on the fluid
Features Include:
• EI 1590 Qualified Filter Cartridges
• Large Surface Area – Allows high flow rate with low initial pressure drop and maximum contaminant holding capacity.
• Resinated Media – Maintains strength resists effects of water and heat.
• 75 PSI Collapse Strength – Heavy gauge carbon steel center tubes give safety margin against pressure surges.
• Coated Steel Components – Resist corrosion from most industrial fluids.
• Corrugated Media – More surface area ensures longer service life.
• Buna-N Gaskets – The best general gasket material available assures positive seal in most fluids.
• Thermoset Bonding Material – Durable endcap-to-media bond prevents internal bypassing
• Threaded base filter cartridges – Available for easier installation.
• These are also available in screw-base design
Applications:
Velcon Pleated Media Cartridges are suitable for a broad range of polar and non-polar fluids. Recommended for applications where the contaminant is granular (non-colloidal), allowing maximum utilization of the high surface area.
Suitable for:
• Jet Fuel
• All Hydrocarbon Fuels
• Cutting Oils
• Glycols
• Degreasing Fluids
• Water Emulsion Coolants
• Naphtha
• Lube Oils
• Ethyl Alcohol
• Insulating Oils
• Toluene
• Synthetic Oils
• Hydraulic Oils
• Diesel Fuel
• Biodiesel Fuel
Specifications:
• Recommended changeout differential pressure - 25 psid
• 75 psi Collapse strength
• Micron ratings from 1/2 to 75
• 98%+ Nominal filtration efficiency
• 5 - 9 Operating pH range
• 250°F Maximum operating temperature
• Multi-pass (Beta Ratio) data available on request
• For information about Flow Ratings with various viscosity fluids, refer to Form #1532
• Flow rate depends on the fluid
| Performance Characteristics | |
|---|---|
| Maximum Operating Temperature (F) | 250, 200 |
| Maximum Operating Temperature (C) | 121, 93 |
| Filter Type | Particulate |
| Application | Aviation Fuels/Industrial, Natural Gas, Ethanol |
| pH Range (Continuous Operation) | 5 - 9 |
| Brand | Velcon |
| Flow Rate | Depends on fluid viscosity and application. See brochure for more information. |
